HG-30L diaphragm Vacuumpump positive and negative pressure dual-use type 1 grade
Extraction speed: 30L/min, > 0.085 (150mbar), positive pressure: 40Psi, series: 1, motor power 180, size mm: 250 * 135 * 210, 8kg, < 50dB, function: positive and negative pressure dual-use type
HuXi
HG-30L
1. Introduction
HG series diaphragm vacuum pump is a new type of diaphragm vacuum pump independently developed and produced by our company. It can run continuously in oil-free state, with low noise, high working efficiency and long service life. Our company has a wide range of product models, with different application ranges, including a vacuum pump and a compressor pump used as a solvent filtration device, a high vacuum pump for rotary evaporator, and a pump with positive and negative pressure for suction filtration, which greatly reduces your laboratory procurement cost. The main advantages are: vacuum stability, adjustable pressure, small size, light weight, easy to use, oil-free, clean and pollution-free, long-lasting and stable work, continuous 24-hour operation, simple repair and maintenance, self-operation. It is mainly used in vacuum distillation, reaction kettle, vacuum filtration, vacuum concentration, vacuum drying, compression and conversion of gas, etc.
Second, technical parameters
| Model | HG-30/HG-30F | HG-30L/HG-30LF | HG-30D/HG-30DF | HG-60DL/HG-60DLF |
| Pumping speed(L/min) | 30 | 30 | 30 | 60 |
| Ultimate Pressure(Mpa) | >0.085 | >0.085 | >0.095 | >0.085 |
| (150mbar) | (150mbar) | (50mbar) | (150mbar) | |
| Positive Pressure (Psi) | — | 40 | — | 40 |
| series | 1 | 1 | 2 | 2 |
| Motor power(W) | 180 | 180 | 180 | 180 |
| Size L×W×H (mm) | 250×135×210 | 250×135×210 | 315×135×210 | 315×135×210 |
| weight | 7.5 | 8 | 13 | 13 |
| Diaphragm material | Imported corrosion-resistant rubber | Imported corrosion-resistant rubber | Imported corrosion-resistant rubber | Imported corrosion-resistant rubber |
| Noise (dB) | <50 | <50 | <50 | <50 |
| function | Negative pressure | Positive and negative pressure dual-purpose type | Negative pressure | Positive and negative pressure dual-purpose type |
Operating Instructions: Please read this instruction manual carefully before you use this product. Only a qualified engineer or electrician can install and commission this product
3. Use of the product
● This product can only be used for air extraction
● It is forbidden to allow corrosive liquids or particulate materials to enter the pump, and water vapor, oil pollutants or other liquids need to be filtered out first.
● The working environment temperature should not exceed 55°C.
● This product should not be used at high altitudes, as low air pressure will affect the product at high altitudes.
● The product is a precision instrument, and the product is protected from dirt and moisture.
Fourth, installation
● Please disconnect the power supply before installation or maintenance, otherwise it will lead to electric shock or casualties.
● In order to avoid electric shock, do not use this product in an environment that comes into contact with water or other liquids. In case of rain and snow, be sure to pay attention to protect the machine.
● The wiring of the motor should be configured in accordance with the local power regulations.
● Check whether the local voltage is consistent with the machine (see label). If the voltage is not the same, use a transformer.
● During the use of this product or just after using this product, do not touch the motor shell to avoid hot hands.
● This product does not need lubrication.
● The size of the connecting hose must match the air inlet.
● Install the muffler provided by us at the air outlet.
5. Placement
● In order to reduce noise and vibration, the product can be placed on the shockproof device, which is placed on a horizontal tabletop, which can reduce resonance.
● Make sure that the vents of the product are unblocked, otherwise the heat dissipation will be affected.
● Connect the power supply and turn on the power switch.
6. Handling of abnormal situations
● Disconnect the power supply.
● Do not disassemble when the power supply is not disconnected.
● Wait for the pump to cool down.
● Refer to common troubleshooting.
● Get in touch with the manufacturer or dealer for more help.
● The motor of the product is equipped with an overheat protector, so as to ensure that the product will not be damaged due to overheating or overload.
7. Product maintenance
● Please disconnect the power supply after using the product to insulate the product.
● Drain the pressure in the pump.
● In a dirty environment, the filter material will be particularly easy to get dirty, so please replace it regularly.
HuXi HG-30L VacuumpumpSpecifications
| LIST | VALUE |
|---|---|
| Pumping rate | 30L/min |
| ultimate pressure | ＞0.085Mpa（150mb） |
| positive pressure | 40psi |
| series | 1 |
| Motor power | 180W |
| size | 250*135*210mm |
| Weight | 8kg |
| Diaphragm material | Imported corrosion-resistant rubber |
| Noise value | <50dB (A) |
HuXi HG-30L Vacuumpump Packing list
Vacuum pressure gauge (-0.1Mpa) X1 piece, connecting hose (Φ7mm * Φ13mm * Φ1000mm) X1 piece, muffler X1 piece, manual X1
[Note] Because the manufacturer's packaging may be updated or upgraded, the detailed packaging list shall be subject to the latest standard configuration of the manufacturer.