Netherlands TQC VF2255 Wet Film Wheel Thickness Wheel Thickness Gauge 0~ 100μm
Netherlands TQC VF2255 wet film thickness gauge range 0~ 100μm, sub-scale 10μm, accuracy +/- 2μm, shape roller type, VF2255 wet film thickness gauge not only on flat substrates, and can be measured on curved substrates.
-
UK ELCOMETER Elcometer 155 QCB15513573-5 Uncured powder coating Wet Film Comb Certificate
1470.0 RMB -
AMITTARI AC-2000 Four Corners Wet Film Comb, Wet Film Card 25~ 2032µm
180.0 RMB -
TRUIT TR 5502/1200 Double-sided wet-film gauge wet film thickness gauge comb type 50~ 1200μm
250.0 RMB -
SHG-700 wet-film gauge YONGLIDA film thickness range is 250~ 700μm
280.0 RMB -
TQC Sheen LD2020 Disposable Plastic Wet Film Comb wet-film card 500pcs/pack
3010.0 RMB
Picture show
Introduction
TQC brand wet film thickness measurement wheel, the roller thickness gauge is designed according to ISO2808-74, and uses the scale of the wheel rail eccentric to roll to obtain the wet film thickness, expressed in μm. Suitable for measuring the wet film thickness of paint. A measuring tool for measuring the wet film thickness of paint, varnish and other paints.
This thickness gauge can not only measure on flat substrates, but also on curved substrates, with high measurement accuracy. The outer rim is engraved with notches so that the outer rim can be pressed tightly into the base plate and prevent slipping. It is made of stainless steel and the hand-held part is made of aluminum.
Features and advantages
1. Designed and produced in accordance with ISO2808-74 standards. There are notches on the outer wheel. The outer edge can fit more closely to the base plate, firmly grasp the surface of the measurement base plate and prevent slipping.
2. Suitable for measuring the wet film thickness of coatings, paints, varnishes, etc.
3. The entire paint wet film thickness meter is made of stainless steel, and the hand-held part is made of aluminum.
4. Equipped with precision roller bearings
Model
model | Measuring range | scale |
VF2255 | 0~100μm | 10μm |
VF2256 | 0~300μm | 30μm |
VF2257 | 0~600μm | 60μm |
Other parameters | ||
Accuracy | ±2μm | |
Material | The hand grip part is made of aluminum, the rest is made of stainless steel |
Instructions
Translated version:
1) Hold the central axis of the wet film thickness measuring wheel. Starting with the largest film thickness scale value reduces the risk of inaccurate measurements due to surface tension.
2) During the test, let the wheel roll through the wet film and the wheel should touch the substrate. The wet film thickness measurement wheel rolls forward and backward for at least one turn. The rolling process should be slow enough to make full contact between the wheel and the coating. Finally, the reading at the end of the wetted portion of the center wheel is the wet film thickness. (It is recommended to measure twice in the same way at different locations to obtain representative values ââwithin a certain range)
3) Use a wet film thickness measuring wheel on the pipe to measure the entire longitudinal axis (longitudinal) of the pipe.
4) For a hard plane, measure the peak value on the surface, which represents the minimum wet film thickness.
Original English version:
Hold the wheel by its central spindle. Begin at maximum thickness to reduce risk of inaccuracy caused by surface tension.
Roll the wheel through the wet film with the side 1 in the diagram touching the substrate. Roll for at least one whole turn and slowly enough for wetting to occur. Roll the wheel backwards by at least on complete turn. The wet film thickness is read from the scale, at the end of the wetted segment of the middle circle, 2 in the diagram.
To use wheel on pipes, measure across the longitudinal axis (lengthways) of the pipe.
On rough surfaces, measurements will be made from the surface peaks and represent the minimum wet film thickness.
Precautions for use
1. After the paint is applied to the test panel, the thickness of the wet paint film should be measured as soon as possible to reduce the thinning of the paint film caused by solvent evaporation.
2. The wet film thickness measuring wheel uses a robust design and is a precision tool. Do not drop or knock the wet film thickness measurement wheel.
3. After use, the wet film thickness measuring wheel should be cleaned immediately.
4. Use a soft rag to clean the wet film thickness measuring wheel. Do not use mechanical cleaning equipment such as wire brushes or abrasive paper. In addition, the use of corrosive cleaning agents may cause long-term damage to the wet film thickness measuring wheel.
5. The wet film thickness measuring wheel should be placed in the box when not in use.
Product actual pictures
TQC VF2255 wet film wheel
TQC VF2256 wet film wheel
TQC VF2257 wet film wheel
Take you into the Dutch TQC
TQC VF2255 Wet Film WheelSpecifications
LIST | VALUE |
---|---|
Range | 0~100μm |
Scaling | 10μm |
Accuracy | ±2μm |
shape | Roller type |
material | Handgrip part is aluminum, Miscellaneous is stainless steel |
Weight | 148g |
Appearance size | 90*22*22mm |
Application standard | ISO2808-74 |
TQC VF2255 Wet Film Wheel Packing list
Wet Film Wheel x1
[Note] Because the manufacturer's packaging may be updated or upgraded, the detailed packaging list shall be subject to the latest standard configuration of the manufacturer.
TQC VF2255 Wet Film Wheel Comment
FAQ
- Tide Review: Cylindrical Bending Tester SP1820
- Operation method steps of small coating machine in TQC laboratory in the Netherlands
- Netherlands TQC SP0500 swing rod hardness tester specific operation method
- How to install and set up the Netherlands TQC SP0500 Swing Bar Hardness Tester?
- TQC Pencil Hardness Tester Instruction Manual
- TQC RV2100 Digital Display Thermohygrometer Instruction Manual
- How to use TQC SP1830 cone shaft bending tester
- Netherlands TQC SP1570 Copy Tape Tester Operation Manual
- TQC Paint Film Impact Tester Operation Instructions
- The specific operation method of TQC SP1820 cylindrical bending tester
- ActiveHG/T 20720-2020
- ActiveISO 2808-2019
- ActiveJJF 1484-2014
- ActiveASTM D1212-2020
- AbolishISO 2808-2007
- ActiveGB/T 8923.1-2011
- ActiveGB/T 13452.2-2008