MODERNER QTX Flexibility tester national standard GB1731
QTX film resilience measurement, in line with the GB1731 standard, 7 different steel shaft rod, the minimum diameter of the shaft rod does not cause damage to the paint film indicates the flexibility of the paint film.
Picture show
product description
MODERNER QTX paint film flexibility tester, also known as paint film elasticity tester, can be used to measure the paint film flexibility according to the national standard GB1731. The flexibility of the paint film is expressed by the minimum diameter of the rod that does not cause damage to the paint film.
Structure of paint film flexibility tester
It consists of seven steel shaft rods with different diameters. It is fixed on the seat frame, and the seat frame can be fixed on the edge of the table of the test bench with screws. The dimensions of each shaft are as follows:
Shaft | size |
Shaft length: | 50 mm |
Shaft 1: | Diameter F15±0.05mm |
Shaft 2: | Diameter F10±0.05mm |
Shaft 3: | Diameter F 5±0.05mm |
Shaft 4: | Diameter F 4±0.05mm |
Shaft 5: | 10mm×3±0.1mm, radius of curvature 1.5±0.1mm |
Shaft 6: | 10mm×2±0.1mm, radius of curvature 1±0.1mm |
Shaft 7: | 10mm×1±0.1mm, radius of curvature 0.5±0.1mm |
After the flexibility tester is assembled, the perpendicularity tolerance between each shaft rod and the installation plane shall not be greater than 0.1 mm.
real shot
Steps
(1) The measurement should be carried out at 23°C±2°C and relative humidity not greater than 70%.
(2) The test panel should be smooth without any visible cracks and wrinkles.
Size: 120mm×25mm×0.2~0.3mm tin plate.
(3) Press the paint film of the test panel upwards with both hands, and press it tightly on the shaft rod with a specified diameter. Use the strength of two thumbs to bend the test board around the shaft rod within 2 to 3 seconds. After bending, the two thumbs should respond Said on the shaft centerline.
(4) After bending, observe the paint film with a 4x magnifying glass. Check whether the paint film is damaged by texture, cracks and peeling.
(5) During the test, the test should be carried out on each shaft rod in order from large to small, and the flexibility or elasticity index of the paint film should be represented by the smallest diameter of the shaft rod that does not cause paint film damage.
Moderner QTX Flexibility testerSpecifications
LIST | VALUE |
---|---|
shaft rod | size |
Shaft length | 50mm |
Shaft rod 1 | Φ15mm |
Shaft rod 2 | Φ10mm |
Shaft rod 3 | Φ5mm |
Shaft rod 4 | Φ4mm |
Shaft rod 5 | 3 * 10Mm, radius of curvature 1.5mm |
Shaft rod 6 | 2 * 10Mm, radius of curvature 1mm |
Shaft rod 7 | 1 * 10Mm, radius of curvature 0.5mm |
Moderner QTX Flexibility tester Packing list
Tester x1
[Note] Because the manufacturer's packaging may be updated or upgraded, the detailed packaging list shall be subject to the latest standard configuration of the manufacturer.
Moderner QTX Flexibility tester Comment
FAQ
- Modern environment full range of product selection table [selection]
- Determination of film flexibility and its application
- What are the common causes of paint failure?
- Adhesion performance of film
- Detection of coating flexibility
- What is film flexibility and how to measure it?
- Solid dry film performance inspection
- How is film flexibility measured?
- Effect of Ultraviolet curing paint Spreader on Wooden ground floor film performance
- Several common methods for testing coating flexibility
- ActiveGB/T 22374-2018
- ActiveHG/T 3369-2003
- ActiveHG/T 3349-2003
- ActiveGB/T 1731-2020
- ActiveHG/T 3829-2006
- ActiveGB/T 23455-2009
- ActiveJT/T 821.2-2011
- ActiveJT/T 821.1-2011
- AbolishGB 12441-2005
- ActiveHG/T 2003-1991
- ActiveGB/T 6745-2008
- ActiveJB/T 9857-2010
- AbolishGB/T 1748-1979
- AbolishGB/T 1731-1993