MODERNER KS-370B Coating Blue-devil Dispersion Testing Machine, Column Clamping Bottle Type
Column clamping type, motor power 550W, crankshaft speed 660rpm, spindle reciprocating amplitude 16mm, spindle swing vibration angle 30deg, Power frequency 220V.
-
Huxi HR-2200BPF lifting platform pilot Disperser
$ 1529.49 -
Qiwei GFJ-0.5 (GFJ-550) LABOratory Small Disperser (High Speed Frequency Conversion)
$ 437.76 -
China small high speed dissolver GFJ2800 Power 3KW electric lift
$ 1405.78 -
MODERNER KS-370C Coating Rapid Dispersion Testing Machine, Floor-to-Floor Clamp Type
$ 1408.87 -
TRUIT TR 2001/7 High Speed Disperser 750W
$ 1104.24
Introduction
Modern environment KS-370 column type paint rapid dispersion testing machine (also known as Blue-devil) includes KS-370A (column clamping tank) and KS-370B (column clamping bottle)Two models. The jar clamping configuration can hold various user-prepared cans (no more than 2.5L on each side, 5L in total on both sides), and the bottle clamping configuration has small glass bottle clamps (4 can be placed on each side, eight in total on both sides). indivual). The volume of the small glass bottles provided is approximately 195mL. The column type is more convenient for picking and placing materials. It is suitable for fast and effective shaking and sharing of materials in laboratories such as coatings, dyes, and inks. It can also conduct comparative dispersion tests of multiple materials at the same time.
The motor power of this KS-370B column clamp bottle paint dispersion testing machine is 550W, and the crankshaft speed is 60rpm.
Actual pictures
Product installation instructions
(1) Install the suction feet on the bottom plate of the column bracket;
(2) After the column is in place, use expansion screws to fix the rubber stoppers around the bottom plate of the column (as shown in the picture);
(3) Install the main unit on the column bracket.
Steps
1. Put the materials to be dispersed and the grinding media (grinding beads) into the tank (or bottle). For the material-bead mass ratio, please refer to the table below.
grinding media | glass bead | steel ball |
Material-bead mass ratio | 1:2~3 | 1:3~4 |
2. Place the sealed tank (or bottle) into the clamping device and turn the handle to clamp it. The clamping force must be appropriate to avoid damaging the can (or bottle) due to excessive force or causing damage to the clamping device.
3. Try to avoid using cans (or bottles) on one side. If you do need one-sided use, clamp a weighted can (or bottle) of water on the other side.
4. If small glass bottles are used in the clamping jar configuration, in order to improve the dispersion efficiency, two small glass bottles can be clamped at a time at a symmetrical position near the outside of the single-side clamping plate. (Pay attention to the balance on both sides of the clamping device)
5. According to the required grinding time, set the timer (randomly supplied, please refer to the timer manual for operation), and start the KS-370 column-type paint rapid dispersion testing machine .
6. After the dispersion is completed, please make sure that the KS-370 column-type paint rapid dispersion testing machine is completely stationary before turning the handle to loosen the clamping device and take out the material tank (or bottle).
7. After the work of the KS-370 Column Type Paint Rapid Dispersion Testing Machine is completed, please disconnect the power supply and perform cleaning and care work in time.
Note: Customers are asked to check the relevant regulations of different products for the detailed steps and judgment standards of material operation, which are not within the scope of the instructions of the testing machine.
How to use the four-hole holder configured to clamp bottles
1. Loosen the ingot nuts at both ends and separate the four-hole holder up and down.
2. Place the small glass bottle into the lower holder (the same specifications as the small glass bottle provided with the machine).
3. Cover the upper holder and tighten the ingot nuts at both ends.
4. Install the entire holder on the Blue-devil holder.
5. When installing, please note that the two grooves on the four-hole holder need to be aligned with the cylindrical pins on the Blue-devil holder; the positioning block on the four-hole holder needs to be above the Blue-devil holder.
Precautions for use
1. After using the new KS-370 column type paint rapid dispersion testing machine for 100 hours, please replace the crankcase lubricating oil. In the future, you only need to check and add it in time for daily use.
(Lubricating oil brand: Great Wall brand heat setting machine lubricating oil 4402-1)
2. The total mass of the clamped material tank (or bottle) should not exceed 5 kilograms to avoid shortening the service life of the paint rapid dispersion testing machine.
3. Please clean and maintain the guide rod and screw of the holder in time to avoid rust or residual foreign matter that may cause difficulty in clamping.
4. The paint rapid dispersion testing machine will generate a lot of heat when working. The paint rapid dispersion testing machine needs to be placed in a workplace with good ventilation conditions.
5. In order to extend the service life of the paint rapid dispersion testing machine , after each operation exceeds 90 minutes, please stop the machine for 10 to 15 minutes to allow the paint rapid dispersion testing machine to dissipate heat before starting again.
Moderner KS-370B Coating rapid dispersion testing machine (column clamping bottle)Specifications
LIST | VALUE |
---|---|
Motor Power | 550W |
Rotation speed of crankshaft | 660rpm |
Spindle reciprocating amplitude | 16mm |
Spindle oscillation angle | 30deg |
Power supply voltage | 220V 50Hz |
Dimension | 800*520*1090mm |
Host weight | 81kg |
Moderner KS-370B Coating rapid dispersion testing machine (column clamping bottle) Packing list
Host x1, timer x1, handle x1, sealing ring (two small and one large) x1, transmission belt x1, rubber pad (for clamping) x4, rubber suction foot x8, rubber stopper x4, 10m expansion screw x8, small glass bottle x8, manual x1
[Note] Because the manufacturer's packaging may be updated or upgraded, the detailed packaging list shall be subject to the latest standard configuration of the manufacturer.