One-piece ordinary type; with the characteristics of small measurement error, high reliability, good stability, and easy operation, it is an indispensable non-destructive testing instrument for controlling and ensuring product quality.
1. Product description
*This instrument is a battery-powered portable measuring instrument, which uses the principle of magnetic induction and eddy current. The measurement method complies with international standards ISO2178, ISO2360 and national standards Gb4956, Gb4957. It adopts computer technology, non-destructive testing technology and other professional technologies to accurately measure the thickness of the measured object without damaging it.
*F-type probe can directly measure the thickness of non-magnetic coating layer (such as: paint, plastic, enamel, copper, aluminum, zinc, chromium, etc.) on the surface of magnetic conductive material (such as iron, nickel). It can be applied to the thickness measurement of electroplating layer, paint layer, enamel layer, aluminum tile, copper tile, babbitt tile, phosphating layer, paper, and also can be used for thickness measurement of hull paint and attachments of underwater structural parts.
*Nf type probe can measure the thickness of the insulating covering layer on the non-magnetic metal substrate, such as paint, plastic, rubber coating on the surface of aluminum, copper, zinc, non-magnetic stainless steel and other materials, and can also measure the thickness of aluminum or aluminum alloy materials Anodized layer thickness.
*The spring guide sleeve probe with wear-resistant hard metal probe can not only measure on hard or rough surfaces, but also ensure that the probe has constant pressing force and stable sampling value.
* Wide measurement range and high resolution.
* Automatic memory calibration value, easy to use.
* Integrated structure, small size and light weight.
*Digital backlight display, no parallax.
*Using the optional RS232C software and cable, it can communicate with PC computer to realize the functions of data collection, processing, analysis and printing.
*The instrument is equipped with automatic shutdown to realize power saving function.
2. Technical specifications
Display: 4-digit backlit LCD Standard test range: 0~1250um (other measurement ranges can be customized)
Resolution: 0.1um (below 100um)
1um (less than 100um)
Measurement accuracy: ±1~3%n or ±2.5um
The thinnest substrate: 0.3mm
Minimum curved surface: F—convex 1.5mm/concave 25mm
N—convex 3mm/concave 50mm
Measurement mode: single measurement and continuous measurement
Operating conditions: temperature 0°C~50°C; humidity <80%
Power supply: 2x1.5vAAA7# batteries
Size: 130x63x24mm
Weight: 90g (without battery)
Standard accessories
*host
*Iron base
* Aluminum base
*Wrist strap buckle
*Calibration diaphragm
*Carrying case
*user's Guide
Optional accessories
*RS-232C interface
USB data line output
data line
* Bluetooth Bluetooth data output
4. Measurement procedure
4.1轻按电源键，接通整机电源后，仪器自动进入测量状态。
4.2在确认校准正确的前提下，就可开始测量。若对以前的校准有所怀疑的话，应再进行一次校准。校准的具体方法详见仪器的就可开始测量。若对以前的校准有所怀疑的话，应再进行一次校准。仪器一旦校准，校准结果将自动存贮在仪器中下次开机测量时，可不必再次进行校准，除非对测量的准确性有怀疑。
4.3将测量传感器压紧到被测涂层上，显示器上的值即为待测涂层的测量值。
注意：由于所有的磁性涂层测厚仪都是采用电磁感应原理；非磁性涂层测厚仪采用电涡流的原理，因此，一定要注意探头压上被测体的速度不能太慢。否则，会造成人为测量误差。
4.4要进行下次测量，需要将测量传感器提起到1厘米以上,然后再重复4.3。
4.5要改变涂层测厚仪的测量单位，即在“um”和“mil”之间实现转换，只要按下“校零键/电源键”，大约6秒钟后，屏幕上就会出现“UNIT”然后松开“校零键/电源键”即可。
4.6要更换测量模式，实现单次测量和连续测量的转换，只要轻按电源键不放，直到显示器上出现“SC”才松开按键即可（从按下电源键到出现“SC”大约需要“9s”）。若显示器上有符号，表示测量模式为连续测量，测量时，蜂鸣器不响。否则为单次测量模式，每测量一次，蜂鸣器都响一下。
4.7测量完毕，轻按电源键关断电源。本仪器设有两种关机方式，即手动关机和自动关机。在任何时侯，只要轻按一下电源键，就可手动关断整机电源；另一方面，若在50秒钟的时间内，未按动任何按键，则会自动关机，以实现省电功能。
5.仪器校准
将测量探头压在基准块上（或不带涂层的测量体上），再轻按一下电源/校零键进行校零。在按电源/校零键时，测量探头在基准块上不要晃动。同时要注意，只有在按完电源/校零键后，才能提起探头，否则，校零不正确。
6.注意事项
6.1为了减少测量体材质对测量精度的影响，建议采用不带涂层的测量体或与测量体材质相同的标准试块作为校准用基准块。
6.2测量完毕，轻按一下电源键，关断整机电源。并在测量头的触头及基准块上涂少许油脂以防生锈。
6.3 The instrument has an automatic shutdown function, if no operation is performed for about 50 seconds, it will automatically shut down.
6.4 The instrument should prevent severe vibration and impact. After use, wipe off the oil on the surface of the instrument and put it in the instrument box for safekeeping.
6.5 It is strictly forbidden to knock or collide with the probe so as not to affect the performance of the probe.
7. Battery Replacement
7.1 When the battery voltage is about 2.5V, the battery symbol will appear on the display, and the battery needs to be replaced.
7.2 Open the battery cover and take out the battery.
7.3 Install the battery correctly according to the label on the battery box.
7.4 If the meter will not be used for a long time, please take out the battery to prevent the battery from rot and damage the meter.
8. Computer connection
8.1 According to the label on the battery box, use the optional "USB data line output", "RS232C data line output" and "Bluetooth Bluetooth data line output" to communicate with the computer to realize data collection, processing, analysis and printing and other functions. Please refer to the online instructions for specific operations, and install the battery correctly.
