Defelsko N45S split 45 ° micro probe, thin coating

Full range of probe details

Detachable built-in probe

F，N，FN，FT

Suitable for one-handed operation

Detachable built-in probe	Probe model	F、N、FN			FT
	range	0~60 mils			0~250mils
		0~1500μm			0~6mm/0~6000μm
	precision	+ (0.05 mils + 1%)  0~2 mils + (0.1 mils  +  1%)  > 2 mils			+ (0.5 mils + 1%)  0~100 mils + (0.5 mil + 3%) > 100 mils
		+ (1 um + 1%)  0~50 um + (2 um + 1%)  > 50 um			+ (0.01 mm + 1%) 0~2.5 mm + (0.01 mm + 3%) > 2.5 mm
	Accuracy is calculated by adding a fixed value to the percentage of readings

Split conventional probes

FS，NS，FNS，NAS，FTS

These constant-pressure, stainless steel probes are hermetically sealed and completely waterproof – ideal for underwater measurements.

Regular	Probe model	FS、NS、FNS	NAS	FTS
	range	0~60 mils	0~25 mils	0~250 mils
		0~1500 um	0~625 um	0~6 mm/0~6000 μm
	precision	+ (0.05 mils + 1%)  0~2 mils + (0.1 mils  +  1%)  > 2 mils	+ (0.02 mils + 1%)  0~4 mils + (0.1 mils + 3%)  > 4 mils	+ (0.5 mils + 1%)  0~100 mils + (0.5 mil + 3%) > 100 mils
		+ (1 um + 1%)  0~50 um  + (2 um + 1%)  > 50 um	+ (.5 um + 1%)  0~100 um  + (2 um + 3%)  > 100 um	+ (0.01 mm + 1%) 0~2.5 mm + (0.01 mm + 3%) > 2.5 mm
	Accuracy is calculated by adding a fixed value to the percentage of readings

FXS Xtreme™

Uniquely designed for applications with rough surfaces. The measuring surface of the FXS Xtreme™ probe is a zirconia toughened alumina wear surface, which is ideal for measuring rough steel surfaces.

Increases the measurement speed to 50 readings per minute, making it suitable for fast measurement of large, rough surfaces. The scan mode increases the rate of measurement to more than 100 readings per minute. (Only PosiTector Premium models have a scan mode)

Compatible with PosiTector mainframes with serial numbers greater than 700,000 and the new Positector SmartLink.

FXS Xtreme™
	range	0~1500 um
		0~60 mils
	precision	+ (0.05 mils + 1%)  0~2 mils + (0.1 mils  +  1%)  > 2 mils
		+ (1 um + 1%)  0~50 um + (2 um + 1%)  > 50 um
	Accuracy is calculated by adding a fixed value to the percentage of readings

Split 90° conventional probe

FRS，NRS，FNRS

Right-angle probes are suitable for measuring low headroom areas.

These constant-pressure, stainless steel probes are hermetically sealed and completely waterproof – ideal for underwater measurements

90° conventional type	Probe model	FRS、NRS、FNRS
	range	0~60 mils
		0~1500 um
	precision	+ (0.05 mils + 1%)  0~2 mils + (0.1 mils  +  1%)  > 2 mils
		+ (1 um + 1%)  0~50 um + (2 um + 1%)  > 50 um
	Accuracy is calculated by adding a fixed value to the percentage of readings

FNDS

The PosiTector 6000 FNDS probe simultaneously measures the thickness of paint and zinc layers in a composite coating system in a single readout.

Composite coating systems use a combination of two corrosion protection systems – typically painted or powder coated on galvanized steel (thermal, electrical, or zinc-sprayed metal). resultantCorrosion protection due toanySeparate protection system.

In composite mode, the positector 6000 FNDS is usedmagnetic induction(ferrous) and eddy current (non-ferrous) principles that simultaneously calculate and display individual coating and zinc layer thicknesses. The magnetic induction principle is used to measure the total thickness of the lacquer/zinc layer on a ferrous substrate, while the eddy current Thickness Gauge principle is used to measure the thickness of the paint layer on a non-ferrous zinc layer. The zinc layer thickness is calculated by subtracting the thickness of the paint layer from the total lacquer/zinc layer thickness. The schematic diagram is as follows,

When not available, the gauge is like a traditional ferrous/non-ferrous dual-function gauge (similar topositector 6000 FNS probe）. It is suitable for measuring the thickness of non-magnetic coatings on steel and non-conductive coatings on non-ferrous metal substrates.

Positicctor Advanced (serial number 730000+) and color LCD are compatible with the Positicctor standard gage. A simple Thickness Gauge update is required.

FNDS
	range		0~60 mils/0~1500 um
	Composite coating	Minimum zinc layer thickness	0.5 mil (13 um)
		Paint layer accuracy	Mils	+ (0.05 mils + 1%)  0~2 mils + (0.1 mils  +  1%)  > 2 mils
			μm	+ (1 um + 1%)  0~50 um  + (2 um + 1%)  > 50 um
		Zinc layer accuracy	Mils	+ (0.1 mils + 1%)  0.5~2 mils + (0.2 mils  +  1%)  > 2 mils
			μm	+ (2 um + 1%)  13~50 um  + (4 um + 1%)  > 50 um
	Accuracy is calculated by adding a fixed value to the percentage of readings

Split 0° probe

F0S，N0S

With a minimal measuring tip and very good thin-film measurement accuracy, this probe is suitable for measuring small parts, hard-to-reach areas or near edges.

The straight F0S and N0S miniature probes have a quick-release adapter that allows them to be targeted at a constant pressure on small, flat or curved parts. This adapter is designed on a spring, if you don't need a sleeve, simply unplug it from the probe.

0° miniature probe	Probe model	F0S	N0S
	range	0~45 mils	0~25 mils
		0~1150 um	0~625 um
	precision	+ (0.02 mils + 1%)  0~4 mils + (0.1 mils + 3%)  > 4 mils
		+ (0.5 um + 1%)  0~100 um + (2 um + 3%)  > 100 um
	Accuracy is calculated by adding a fixed value to the percentage of readings

Split 45° miniature probe

F45S，N45S

With a minimal measuring tip and very good thin-film measurement accuracy, this probe is suitable for measuring small parts, hard-to-reach areas or near edges.

45° miniature probe	Probe model	F45S	N45S
	range	0~45 mils	0~25 mils
		0~1150 um	0~625 um
	precision	+ (0.02 mils + 1%)  0~4 mils + (0.1 mils + 3%)  > 4 mils
		+ (0.5 um + 1%)  0~100 um + (2 um + 3%)  > 100 um
	Accuracy is calculated by adding a fixed value to the percentage of readings

Split 90° miniature probe

F90S，N90S

Right-angle probes are suitable for measuring low headroom areas.

With a minimal measuring tip and very good thin-film measurement accuracy, this probe is suitable for measuring small parts, hard-to-reach areas or near edges.

90° miniature probe	Probe model	F90S	N90S
	range	0~45 mils	0~25 mils
		0~1150 um	0~625 um
	precision	+ (0.02 mils + 1%)  0~4 mils + (0.1 mils + 3%)  > 4 mils
		+ (0.5 um + 1%)  0~100 um + (2 um + 3%)  > 100 um
	Accuracy is calculated by adding a fixed value to the percentage of readings

Wide-range probes

FT，FTS，FNTS，FKS，NKS

Suitable for thick coatings such as epoxy resin, rubber, cement, intumescent fire retardant coatings, etc.

Large-scale type			Probe model	FT，FTS，FNTS	FKS，NKS
			range	0~250 mils	0~500 mils
				0~6 mm/0~6000 μm	0~13 mm/0~500 mils
			precision	+ (0.5 mils + 1%)  0~100 mils + (0.5 mil + 3%) > 100 mils	+ (1 mils + 3%)  + (0.02 mm + 3%)
				+ (0.01 mm + 1%) 0~2.5 mm + (0.01 mm + 3%) > 2.5 mm
FT	FTS	FNTS，FKS，NKS	Accuracy is calculated by adding a fixed value to the percentage of readings

FHXS Xtreme

Measure non-conductive coatings on steel substrates

The FHXs Xtreme probe comes with alumina, abrasion-resistant contact surfaces and braided cables for use on hot or rough surfaces. Hot surface temperatures can be as high as 250°C (500°F).

Compatible with PosiTector mainframes with serial numbers greater than 700,000 and the new Positector SmartLink.

FHXS Xtreme
	range	0~400 mils
		0~10000 um
	precision	+ (0.1 mils + 3%)
		+ (2 um + 3%)
	Accuracy is calculated by adding a fixed value to the percentage of readings

FLS

Suitable for measuring intumescent varnish and other thick protective coatings on steel.

● Measure thickness up to 38mm (1.5 inches)

● Braided stainless steel cable - torsion-resistant, abrasion-resistant, shear-resistant

● Includes hard case and 19 mm (750 mil) spacer

Compatible with PosiTector mainframes with serial numbers greater than 700,000 and the new Positector SmartLink.

FLS
	range	0~38 mm
		0~1.5inch
	precision	+ (0.01 in. + 3%)
		+ (0.2 mm + 3%)
	Minimum surface area	3.25 x 3.25 inches (83 x 83 mm)
	Minimum substrate thickness	0.1inch(2.5 mm)
	Accuracy is calculated by adding a fixed value to the percentage of readings

FNGS

Suitable for measuring very thick coatings on all metals. It is particularly suitable for measuring hull coatings and thick intumescent coatings.

● Measure thicknesses up to 63.5 mm (2.5 inches)

● Measure the thickness of non-conductive coatings on magnetic and non-magnetic metal substrates.

● Braided stainless steel cable - torsion-resistant, abrasion-resistant, shear-resistant

● Long-lasting, low-wear probe contact for easy scanning of large areas.

● Includes a handle for easy one-handed operation

● Includes a set of traceable coating thickness standards

● Instruction cards are included

Compatible with PosiTector mainframes with serial numbers greater than 700,000 and the new Positector SmartLink.

Probe Purchase Chart

F – Ironsubstrate(Steel & Cast Iron)

N - NonIronmetalsubstrate(Aluminum, copper, titanium, etc.)

FN – All metal substrates – automatic identification of substrates

Probe x1

[Note] Because the manufacturer's packaging may be updated or upgraded, the detailed packaging list shall be subject to the latest standard configuration of the manufacturer.