CQX CQ-X6 Precision coating Thickness Gauge for automatic substrate identification of coatings on all metals

Product Description

The CQ-X6 precision coating Thickness Gauge is a small-sized handheld precision coating Thickness Gauge produced by Chengqixin. It has a built-in F/N probe and can automatically identify different substrates for thickness measurement.The shell of the CQ-X6 precision coating Thickness Gauge is a black hard plastic shell with good wear resistance and a large LCD. The measured thickness range is 0~1250 microns. It is powered by a battery and is suitable for off-site thickness measurement work.

Chengqixin CQ-X6 precision coating Thickness Gauge is a composite Thickness Gauge suitable for coating measurements on all metals. The precision Thickness Gauge depends on the base material when measuring. Each time the reading is displayed, the letters Fe (magnetic conductive metals, such as iron and steel) or NFe (non-magnetic conductive metals, such as aluminum and alloys) are also displayed. The precision Thickness Gauge has a 1.8-inch TFT screen that can simultaneously display the maximum value, minimum value, average value and error value of the measurement process.

Actual pictures

How to operate

1. Press down the probe to automatically turn on the power and start measurement. After 30 seconds of inactivity, the power will automatically turn off.

2. Place the probe of the CQ-X6 precision coating Thickness Gauge squarely on the surface of the coated substrate to be measured. Hold the Thickness Gauge steadily. When the measurement is completed, the precision Thickness Gauge will beep.

3. Pick up the Thickness Gauge and display the reading. (Note: The symbol "------" is displayed when the range is exceeded)

CQ-X6 precision coating Thickness Gauge function operation

1.UVLED: Tap the "+" button once to turn on the UVLED, and tap the "+" button once again to turn off the UVLED.

2.LED: Press the "-" button once to turn on the LED, and press the "-" button once again to turn off the LED.

3. Color change: Press the "+" button for 2 seconds to change the display and font color.

4. Flip the display: Press the "-" button for 2 seconds to flip the display 180 degrees.

5. Unit switching: Press the "M" button 3 times continuously, the buzzer will sound, and the conversion between "um" and "mil" is completed.

6. Calibration:

a) Uncoated calibration: Press the "M" button 2 times continuously, the screen will display "00" and the buzzer will sound "beep, beep, beep...". At this time, place the Thickness Gauge probe flat on the On the surface of the uncoated substrate to be measured, hold it firmly. The Thickness Gauge will beep and the screen will display "0". Pick up the Thickness Gauge and complete the uncoated zero reset.

b) Standard piece calibration: After measuring the standard piece, lightly press the "M" button once, the buzzer will beep, beep, and the current measurement data will flash twice. Then, press the "+" or "-" button to change the reading. Adjust it to be consistent with the standard film. Finally, lightly press the "M" button once and the buzzer will "beep" once to confirm the modified data.

c) Restore factory parameters: Press the "+" or "-" button at the same time, release the button when the buzzer prompts "beep, beep, beep." to complete the factory restore operation.

7. Clear the maximum, minimum, average and error values: Press the "M" button 4 times continuously, the buzzer will sound "beep", and the measured maximum, minimum, average and error values ​​can be cleared.

8.Battery low Voltage alarm:

When "There is an X mark in the battery" appears on the screen, the measured value may be inaccurate. Please replace the battery.

Plastic Encasement box x1, host x1, FE calibrated version x1, NFE calibrated version x1, instrument instruction manual x1, certificate x1, warranty card x1, calibration shim x1

[Note] Because the manufacturer's packaging may be updated or upgraded, the detailed packaging list shall be subject to the latest standard configuration of the manufacturer.