Home> Library> Read
📖

Reader's Guide

This manual is compiled based on manufacturer's data. Due to equipment batch changes, the content may not fully match every physical unit. Please refer to the actual operation and on-device labels.

Copyright belongs to the manufacturer. For internal reference of purchasers only. If safety parameters in the manual differ from the physical unit, please suspend operation and consult our engineer for confirmation.

Disclaimer: This manual is for reference only. In case of any discrepancy, the physical unit shall prevail. Our company assumes no liability for any consequences arising from operations based on this manual.

SMTSER NBC-120 Gravure Printing Proofer Instruction Manual

The SMTSER NBC-120 Gravure Printing Proofer instruction manual introduces the power connection requirements, Touchscreen parameter settings, printing pressure adjustment, point printing cleaning process, and solutions to common faults such as Color deviation and wrinkling.

Intaglio Dot-Printing Sample Machine User Manual

  1. Power connection requirements: 220V, 450W, must be grounded, pay attention to electrical safety.

  2. Before use, clean the rubber roller and intaglio pattern roller thoroughly, and prepare the materials.

  3. Turn on the switch power supply on the side of the machine. Before printing and sampling, you must set the printing data (on the right touchscreen). The settings include: printing speed, appropriate printing pressure (pressure was set before leaving the factory, optional), printing speed (30-300 rpm, about 0-130 meters/minute), and then select the number of turns (1-1.8 turns).

  4. Set the printing pressure (scale display wheel 0-20mm), about 1mm is 0.06mm; the printing pressure should not be too high, recommended 5-8mm. After setting the data, pull the material and balance the film onto the rubber roller surface, locking the squeegee pressure. First, set the number of turns and speed, then press "Position," then press "Press," the pipette drips ink, and you click "Spot Print" to print. The servo motor will execute the program based on the set number of turns. After completing the action, press "Clean." Clean slowly, repeat cleaning, and do not block the mesh.

  5. After the operation, turn off the power. If special situations arise during operation, immediately press the "emergency stop" switch. Do not open the chassis for repairs without authorization; it must be handled by a professional electrical mechanic. This model has a computer program system that cannot be powered off for long periods. It can be plugged in twice a month for 10 minutes each time, with internal capacitor charging. During thunderstorms, it is recommended not to turn on the machine to avoid damaging electronic components.

Circle count settings
1 - 1.8 laps
Speed settings
30-300 rpm
Home Page
Main interface
Control panel diagram        
Managing pages
Positioning Positioning
Printing Printing
Pressure Roll Press roller
Cleaning Cleaning
Home Page Main page
Parameter set parameters Parameters

Operating procedures

  1. Prepare the film and ink, and clean the anilox roller and rubber roller.

  2. Attach the film to the rubber roller.

  3. Next, position the rubber roller by aligning its positioning plate with the adjacent positioning pin.

  4. Lock the scraper tightly.

  5. Press "Position" (anilox roller positioning).

  6. Press the "press" rubber roller and the anilox roller together.

  7. Press "Click to Open". The computer program executes data settings.

Precautions and Symptoms: Pay attention to the ink's viscosity (usually 15-20 seconds for 3# cups). Low viscosity may cause tearing; low viscosity allows you to adjust the speed accordingly. If lines appear on printed color samples, it is because the squeegee blade is not tightened; if lines appear in blank areas, it is caused by cracks in the squeegee. If the printed color sample has pinholes, increase the pressure slightly. If the color sample shows creases or tearing, adjust the pressure appropriately. To prevent the film from attracting dust from static electricity and affecting printing results, pay attention to the working environment.

2020 model gravure sample machine
Exterior of the gravure sample machine            Details of the sample machine        

Common causes and solutions for color schemes

Causes of fault issuesImprovement and solutions
The intaglio sample machine and the printing press do not have consistent colorsThe ink used on the printing machine must be consistent, the anilox roller parameters must be consistent, and the printing pressure should be appropriate
Printed sample creasing (single-side adjustment)If the pressure on both sides is unbalanced, you need to adjust the pressure back and forth by moving the left and right swing rod screws inside the case. Adjust the screw on the other side if the pressure is insufficient, and don't touch the other side. Adjust the process until the pressure is balanced, and test the effect once after adjustment.
Printed sample dry-forming phenomenonIf the ink has high viscosity and indoor temperature, a slow-drying agent can be added appropriately
Printed samples show tearingLow ink viscosity, adjust ink viscosity appropriately (3# cup: 18-22S)
Printed samples may experience outages or varying depthsChecking the quality of engraving on anilox rollers? Anilox roller blockage plate (dots are clogged): Is the ink drop amount sufficient? Is the ink evenly distributed on the anilox roller?
Blank spots appear on printed samplesIf the printing pressure is insufficient, increase the pressure appropriately and check whether the rubber roller surface is damaged.
Substrate (Film)Printing pressure should be appropriately low
Substrate (paper)Slightly higher printing pressure (1CM ruler display)
Pressure is adjusted bilaterallyCheck if the number of turns is correct. When adjusting balance, first apply zero-contact pressure to the rubber roller, meaning the adjustment button is set to zero turns. Then adjust the screws inside the case.
The display screen does not light upCheck whether the emergency stop switch, wire contact, and leakage switch have tripped
The servo motor does not moveCheck if there is a power supply? Is the program lost? Or lightning weather that disrupts the drive?
Noise occurs when the anilox roller rotatesCheck whether the bearings on both sides of the anilox roller are damaged. Check if the universal joint screw connecting the anilox roller is loose. Or does the right sensor stick collide with the body?
Equipped with a precision spectrometer detectorCompare samples printed on large machines with small sample machines

The document content is organized based on operational usage, with chapter order adjusted to ensure coherent numbering. Some details are objectively described for practical applications.